Talis C14127XX1Installation Instructions / Warranty
10FrançaisInstallez l’obturateur à clapetRetirez le plongeur.Dévissez la collerette de l’obturateur du raccord en T.Dévissez la queue du raccord en T.
11Réglage de la butée limite d’eau chaude (en option)Poussez le cache-vis dans la poignée à l’aide d’une clé hexagonale de 4 mm (). Desserrez la vis
1Instale el tirador.Coloque el grifo y el aro de sellado sobre la supercie de montaje.Instale la arandela de bra, la arandela metálica y la tuerca
13�priete los tornillos tensores con un destornillador.Instale los adaptadores sobre los topes.Instale los ltros.Si no se instalan los ltros, el gri
14EspañolInstale el tapón elevableRetire el émbolo.Desenrosque la brida de salida del drenaje del tubo en “T”.Desenrosque la alcachofa del tubo en “T”
15Ajuste el tope de límite de alta temperatura (opcional)Levante el mando (1). Utilice una llave hexagonal de 4 mm para empujar la cobertura de tornil
1If the ow of water diminishes over time, remove the hose lters.Flush the lters with clear water.Install the lters. onouvertabiertohotchaudcalien
17Replacement Parts / Pièces détachées / Repuestos13457810111.1
181 handle poignée mando 1411XX01.1 screw cover cache vis tapón 338000 ange capot sphérique orón 883XX03 nut écrou tuerca 8840004 cartridge
1Cleaning Recommendation for Hansgrohe ProductsModern lavatory faucets, kitchen faucets, and showers consist of very dierent materials to comply wit
Recommended water pressurePression d’eau recom-mandéePresión recomendada en servicio15 - 75 psiMax. water pressure Pression d’eau maximale Presión má
0Instructions de nettoyage pour robinetteries et douchesVeuillez suivre les instructions du fabricant de produits/articles de nettoyage. De plus, ten
1Limited Lifetime Consumer WarrantyThis product has been manufactured and tested to the highest quality standards by Hansgrohe, Inc. (“Hansgrohe”).
Hansgrohe, Inc. • 140 Bluegrass Lakes Parkway • �lpharetta, G� 30004Tel. 770-30-880 • Fax 770-30-887www.hansgrohe-usa.comUS - Installation Instr
3Installation ConsiderationsFor best results, Hansgrohe recommends that this unit be installed by a licensed, profes-sional plumber.Please read over t
4InstallationInstall the pull rod.Place the faucet and sealing ring on the mounting surface.Install the ber washer, metal washer and mounting nut (1)
5Tighten the tensioning screws using a screw-driver.Install the adapters on the stops.Install the lters.Failure to install the lters may result in u
EnglishInstall the pop-up drainRemove the plunger.Unscrew the drain outlet ange from the tee.Unscrew the tailpiece from the tee. Wrap the threads w
7Set the High Temperature Limit Stop (optional)Lift the handle (1).Use a 4 mm �llen wrench to push the screw cover into the handle (). Use the 4mm �
8Installation Installez la tirette.Placez le robinet et l’anneau d’étanchéité sur la surface de montage.Installez la rondelle en bre, la rondelle mét
Serrez les vis de pression à l’aide d’un tourn-evis.Installez les adaptateurs sur les butées d’arrêt.Installez les ltres.Si ces ltres ne sont pas i
Kommentare zu diesen Handbüchern